YaleGrips are cable grips constructed from Technora® aramid fiber at braid and are assembled in a four-leg configuration extending from a reinforced securing eye. The eye is entirely covered with an extra layer of braid saturated with Maxijacket™ urethane, an abrasion-resistant coating for extended life.
YaleGrips are used as pulling and stopping grips for electrical line construction work both above and below ground, deployment and retrieval of a variety of cables, marine stoppers on hawsers, and temporary or permanent strain relief.
These cable grips are noncorrosive, have good dielectric properties, and are compact and lightweight. When installed, the grip remains flexible and is less damaging to mating surfaces than many conventional grip designs.
YaleGrips may be used for temporary or permanent eyes, either in midspan or at the end of a line.
YaleGrips are significantly stronger than wire mesh grips and do not form the dangerous “fishhooks” associated with wire mesh, making them safer to handle.

Select the grip based on anticipated working load rather than the diameter of the cable it fits. When the anticipated load needs to be distributed over a wider surface area, a six-leg YaleGrip is recommended.
Larger cables may be accommodated by increasing the tail dimension (“L”). Contact Ocean Innovations for sizing assistance or a quotation.

Options include urethanizing the entire grip to extend service life, particularly in active towing applications. Yale refers to this as the “marine treatment.”
YaleGrips can also be manufactured with extended tails to accommodate larger cables. Hardware, such as stainless steel thimbles, may be added to the eye to enhance performance.

YaleGrips are available in the sizes shown below, with each size color-coded for easy identification. Each grip also carries a serialized tag for tracking purposes.
| Diameter (Inches) |
Working Load (Lbs) |
Average Break Strength (Lbs) |
Color | Eye Size (Inches) |
Tail Length (Feet) |
Minimum Cable Diameter (Inches) |
Maximum Cable Diameter (Inches) |
|---|---|---|---|---|---|---|---|
| 7/16 | 1,200 | 6,000 | Red | 6 | 4.5 | 3/16 | 1/2 |
| 9/16 | 2,400 | 12,000 | Blue | 6 | 5.5 | 1/4 | 3/4 |
| 11/16 | 3,600 | 18,000 | Green | 6 | 6.5 | 3/8 | 7/8 |
| 7/8 | 6,000 | 30,000 | Orange | 8 | 8 | 1/2 | 1 |
| 1 | 9,600 | 48,000 | Yellow | 8 | 10 | 5/8 | 1-1/8 |
| 1-1/4 | 14,400 | 72,000 | Black | 12 | 16 | 7/8 | 1-3/4 |
| 1-1/2 | 24,000 | 120,000 | Red | 16 | 22 | 1-1/8 | 3 |
| 1-3/4 | 36,000 | 180,000 | Blue | 18 | 28 | 1-3/8 | 3-1/2 |
| 2 | 58,000 | 290,000 | Green | 18 | 34 | 2 | 4 |
| 2-1/4 | 73,000 | 365,000 | Orange | 20 | 40 | 3-1/4 | 5 |
| 2-1/2 | 90,000 | 450,000 | Yellow | 24 | 52 | 4 | 6 |
| Diameter (mm) |
Working Load (kg) |
Average Break Strength (kg) |
Color | Tail Length (m) |
Minimum Cable Diameter (mm) |
Maximum Cable Diameter (mm) |
|---|---|---|---|---|---|---|
| 11 | 544 | 2,722 | Red | 1.4 | 5 | 13 |
| 14 | 1,089 | 5,443 | Blue | 1.7 | 6 | 19 |
| 17 | 1,633 | 8,165 | Green | 2 | 10 | 22 |
| 22 | 2,722 | 13,608 | Orange | 2.4 | 13 | 25 |
| 25 | 4,355 | 21,773 | Yellow | 3 | 16 | 29 |
| 32 | 6,532 | 32,659 | Black | 4.9 | 22 | 44 |
| 38 | 10,886 | 54,432 | Red | 6.7 | 29 | 76 |
| 44 | 16,330 | 81,648 | Blue | 8.5 | 35 | 89 |
| 51 | 26,309 | 131,544 | Green | 10.3 | 51 | 102 |
| 57 | 33,113 | 165,564 | Orange | 12.2 | 83 | 127 |
| 64 | 40,824 | 204,120 | Yellow | 15.8 | 102 | 152 |
The optional 6-leg YaleGrip distributes the load more evenly across the surface of the cable or substrate. This configuration is particularly useful for handling an umbilical because it helps minimize compression loads.
The 6-leg YaleGrip has the same tensile rating as the corresponding 4-leg model while spreading compressive forces over a wider surface area. Both the 6-leg and 4-leg configurations are available with the optional Maxijacket™ marine coating.
