YaleGrip

Synthetic Pulling & Stopping Grip

YaleGrips are cable grips constructed from Technora® aramid fiber at braid and are assembled in a four-leg configuration extending from a reinforced securing eye. The eye is entirely covered with an extra layer of braid saturated with Maxijacket™ urethane, an abrasion-resistant coating for extended life.

YaleGrips are used as pulling and stopping grips for electrical line construction work both above and below ground, deployment and retrieval of a variety of cables, marine stoppers on hawsers, and temporary or permanent strain relief.

These cable grips are noncorrosive, have good dielectric properties, and are compact and lightweight. When installed, the grip remains flexible and is less damaging to mating surfaces than many conventional grip designs.

YaleGrips may be used for temporary or permanent eyes, either in midspan or at the end of a line.

YaleGrips are significantly stronger than wire mesh grips and do not form the dangerous “fishhooks” associated with wire mesh, making them safer to handle. 

YaleGrip synthetic pulling and stopping grip

Size Selection

Select the grip based on anticipated working load rather than the diameter of the cable it fits. When the anticipated load needs to be distributed over a wider surface area, a six-leg YaleGrip is recommended.

Larger cables may be accommodated by increasing the tail dimension (“L”). Contact Ocean Innovations for sizing assistance or a quotation.

Yale GRIP

Options

Options include urethanizing the entire grip to extend service life, particularly in active towing applications. Yale refers to this as the “marine treatment.”

YaleGrips can also be manufactured with extended tails to accommodate larger cables. Hardware, such as stainless steel thimbles, may be added to the eye to enhance performance.

YaleGrip Resources

YaleGrip Specifications and Data

YaleGrips are available in the sizes shown below, with each size color-coded for easy identification. Each grip also carries a serialized tag for tracking purposes.



Diameter
(Inches)
Working Load
(Lbs)
Average Break Strength
(Lbs)
Color Eye Size
(Inches)
Tail Length
(Feet)
Minimum Cable Diameter
(Inches)
Maximum Cable Diameter
(Inches)
7/16 1,200 6,000 Red 6 4.5 3/16 1/2
9/16 2,400 12,000 Blue 6 5.5 1/4 3/4
11/16 3,600 18,000 Green 6 6.5 3/8 7/8
7/8 6,000 30,000 Orange 8 8 1/2 1
1 9,600 48,000 Yellow 8 10 5/8 1-1/8
1-1/4 14,400 72,000 Black 12 16 7/8 1-3/4
1-1/2 24,000 120,000 Red 16 22 1-1/8 3
1-3/4 36,000 180,000 Blue 18 28 1-3/8 3-1/2
2 58,000 290,000 Green 18 34 2 4
2-1/4 73,000 365,000 Orange 20 40 3-1/4 5
2-1/2 90,000 450,000 Yellow 24 52 4 6
Diameter
(mm)
Working Load
(kg)
Average Break Strength
(kg)
Color Tail Length
(m)
Minimum Cable Diameter
(mm)
Maximum Cable Diameter
(mm)
11 544 2,722 Red 1.4 5 13
14 1,089 5,443 Blue 1.7 6 19
17 1,633 8,165 Green 2 10 22
22 2,722 13,608 Orange 2.4 13 25
25 4,355 21,773 Yellow 3 16 29
32 6,532 32,659 Black 4.9 22 44
38 10,886 54,432 Red 6.7 29 76
44 16,330 81,648 Blue 8.5 35 89
51 26,309 131,544 Green 10.3 51 102
57 33,113 165,564 Orange 12.2 83 127
64 40,824 204,120 Yellow 15.8 102 152

6-Leg YaleGrip

The optional 6-leg YaleGrip distributes the load more evenly across the surface of the cable or substrate. This configuration is particularly useful for handling an umbilical because it helps minimize compression loads.

The 6-leg YaleGrip has the same tensile rating as the corresponding 4-leg model while spreading compressive forces over a wider surface area. Both the 6-leg and 4-leg configurations are available with the optional Maxijacket™ marine coating.

Six-leg YaleGrip synthetic pulling and stopping grip

Call us

(858) 454-4044